Anker SOLIX C800 Canada: Output and Charging Limits
Check the Canadian C800 listing and official A1753 guide for its output, SurgePad, solar, charging, and backup claims.
This profile uses Anker’s Canadian C800 product listing and its official A1753 user guide. Treat the Canadian listing as the market-specific source for the headline configuration. The user guide adds the solar-input voltage and current window, but check that A1753 and the guide’s connector description match the label and physical unit you have. A Canadian product page does not establish that a US or other regional C800 listing has the same plug, firmware, bundle, or electrical limits.
Published C800 specifications
| Field | Canadian listing or A1753 guide | Qualification |
|---|---|---|
| Nominal battery capacity | 768 Wh | Listed capacity; usable energy is not established |
| AC output | 1,200 W; 120 V / 60 Hz | The total rating still applies across the connected AC loads |
| SurgePad | Up to 1,600 W | Not a general 1,600 W continuous rating or a device-compatibility guarantee |
| Solar input | Up to 300 W; guide lists 11–60 V, 10 A, XT60 | All limits apply together; verify connector and unit match |
| AC charging | 750 W standard; 1,100 W UltraFast | The listing says UltraFast is app-enabled |
| AC bypass input | Up to 1,440 W | A separate mode-specific figure; the captured page does not define every load condition |
| UPS switching | 20 ms | Manufacturer-stated transition value, not a device-specific ride-through result |
| Output ports | Five AC, two USB-C, two USB-A, and a 12 V / 10 A car socket | Simultaneous-output and per-port combinations require the exact guide |
The Canadian product page describes the battery as LFP and states a 3,000-cycle figure. A cycle-life headline is not a field-life guarantee: operating temperature, charge rate, depth of discharge, and the manufacturer’s test conditions matter. For a runtime estimate, use the 768 Wh nominal capacity only as a starting input, then account for station consumption, inverter losses, temperature, and the connected load’s real energy use.
Do not treat SurgePad as extra inverter capacity
Anker presents SurgePad as a mode for selected high-wattage loads. The A1753 guide says the feature does not work in bypass mode and is not intended for precision equipment or loads with strict voltage requirements. Its 1,600 W label therefore does not change the standard 1,200 W AC rating into a universal continuous-output ceiling. Check the exact load type, manual instructions, startup demand, and operating mode before relying on it.
The five AC receptacles share the station’s total output budget. The product page’s outlet count does not mean each socket can supply 1,200 W at once. The available source material does not establish every simultaneous-output combination, so use the guide’s table for the exact operating state instead of adding port labels together.
Match the solar and charging input
The listing advertises up to 300 W of solar input. Anker’s A1753 guide gives an 11–60 V input range, 10 A maximum, and an XT60 connection. These are combined compatibility checks: confirm panel open-circuit voltage, current, polarity, connector, and any approved cable for the specific unit. Cold weather can raise panel open-circuit voltage, so a panel that appears to fit by nameplate wattage alone may still exceed the station’s voltage limit.
The listing distinguishes standard AC charging from app-enabled UltraFast charging, and publishes a separate bypass-input value. Charging speed changes with settings and operating conditions; the listed maximum is not a promise that the station will always draw that power. Do not apply the bypass figure to battery-discharge output or assume it defines the output available to a load in every mode.
Check the backup claim with the device maker
Anker publishes a 20 ms UPS switching figure. This does not show whether a particular computer, router, pump, refrigerator, or medical device will continue operating through a transfer. Device behavior depends on its own hold-up time and the station’s actual configuration. Follow both manufacturers’ guidance, and test ordinary equipment before depending on it during an outage. A power station profile cannot approve life-safety use.
The Canadian listing and A1753 guide do not establish an expansion-battery path, independent runtime test, or usable-energy figure for every load. If battery expansion or another market version matters, get confirmation for the exact C800 model number instead of transferring a capability from a different Anker product. See the specification decoder, UPS guide, and charging and expansion guide for the corresponding checks.